HP J9729A Managed Ethernet Network Switch

Product Information

Only supported for use in SFP⁠+ ports on JL658A. 100-FX is not supported for use in any SFP56 ports on other models. The SFP ports on the models listed do not support these 10G SFP⁠+ cables. For use in an installed J9731A Aruba 2920 2-port 10GbE SFP⁠+ . For the J9308A module: K.14.34 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007

For J9310A, J9311A: K.14.50 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483, and J9054D)For use in the JL075A SFP⁠+ ports. Also used in an installed JL083A Aruba 3810M/2930M 4SFP⁠+ MACsec Module. J9772A, J9773A, J9774A, J9775A, J9776A, J9777A, J9778A, J9779A, J9780A, J9781A, J9782A, J9783A, J9853A, J9854A, J9855A, J9856A JL687A 32p 25G module requires configuration of "interface groups" (groups of 4 ports) to enable use of 1G or 10G transceivers or DACs in the SFP28 ports (default is to use 25G transceivers / DACs). See the 8400 For J9451A: K.14.24 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007

J8992A fixed SFP ports are 1GB and do not support these SFP⁠+ copper cables. For use in an installed J9312A 10GbE 2-port SFP⁠+/2-port CX4 yl Module. Is it broken, do you think, or perhaps a firmware or config issue? The switch is on the latest version.

For J8705A and J8706A modules: K.12.01 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007 Not supported for use in the following 3800 models: J9573A, J9574A, J9575A, and J9576A. The SFP⁠+ ports do not support 100M operation. For J9537A, J9549A, J9535A, and J9637A modules: K.15.02.0004 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007 For use in the JL075A 3810M switch or in any 3810M switch with a JL083A Aruba 3810M/2930M 4SFP⁠+ MACsec Module installed. Table 46: ( ArubaOS-CX)Compatibility for the SFP⁠+ DACs (and specifics for HPE Server cables) Product name

Wondering if someone can help please. I've had a 2920 switch for a while but only just getting round to connecting 10GbE to our main Mellanox switch. Strange behaviour with the module showing in the CLI commands but not via the menu, see below. Any attempts to plug in copper cables or fibre modules all result in flashing amber light on either port and the port doesn't go 'up'. For use in the JL075A SFP⁠+ ports or used in an installed JL083A Aruba 3810M/2930M 4SFP⁠+ MACsec Module. JL253A, JL254A, JL255A, JL256A, JL258A, JL263A, JL264A, JL259A, JL260A, JL261A, JL262A, JL557A, JL558A, JL559A For J8692A, J8693A: K.12.01 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483, and J9054D 1990-4483 and 1990-4360) K.12.01 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007

Key specs

The 8325 requires configuration of "interface groups" (groups of 12 ports) to enable the use of 1G or 10G transceivers / DACs in the SFP28 ports (default is to use 25G transceivers / DACs). JL687A 32p 25G module requires configuration of "interface groups" (groups of 4 ports) to enable use of 1G or 10G transceivers or DACs in the SFP28 ports (default is to use 25G transceivers / DACs). See the